Rotary Axis Selection Hub

Crossed Roller Bearing – Rotary Axis

Rotary Axis Selection Hub

Choosing the right rotary axis bearing starts with how the rollers are arranged and how the unit will bolt to the machine. A crossed roller bearing puts cylindrical rollers in a single 90° crossed row, so one unit takes radial load, axial load and tilting moment together. A face mount crossed roller bearing goes a step further: the mounting holes are machined straight into the inner and outer rings, which removes separate fixing flanges and support seats. This hub walks from structure to mounting to sizing so you can shortlist a family before you commit to a part number.

40 – 384 mm Published bore range
Up to 646 mm Outer diameter
22 – 79 mm Width range
Bearings,Rock Precision Engineering Co., Ltd.,Bearings

What a Crossed Roller Bearing Solves

Most rotary axes need one thing at the same time: a short, stiff stack that resists radial load, axial load and tilting moment without eating axial height. The bearing architecture decides whether that is possible in one component or needs two.

Single-row crossed roller layout

  • Cylindrical rollers sit between the rings in a 90° crossed arrangement, alternating in direction.
  • One bearing carries radial load, axial load and tilting moment at the same time.
  • The full bearing width takes the moment, which keeps the axial stack short.
  • Rigidity comes from a single, closely matched pair of ring raceways instead of two separated sets.

Paired angular contact layout

  • Two single-row bearings are mounted apart and usually preloaded against each other.
  • Combined loads are shared across the pair, so load capacity is spread over two positions.
  • The spacing needs a longer shaft and a deeper axial envelope.
  • Preload and seat spacing have to be controlled during assembly, which adds steps and variability.
  • Buyer decisionIf the axial envelope is generous and the load is mostly radial, a preloaded pair remains a well-understood choice. If the axis must stay short, stiff and simple to assemble, compare the crossed roller structure before you spend time on part numbers.

Family Comparison: XU, XSU, SX, YRT and RB-Style

These are the families most often quoted for rotary axes. Only the XU row is drawn from published Rock specification data. The other rows show what has to be confirmed with the supplier before you specify, so the table works as a question list rather than a claim list.

Family Structure Mounting approach Ring rotation Fixing flanges / support seats Relative rigidity What to confirm
XU Series (integrated) Integrated inner and outer ring construction with pre-machined mounting holes Direct face mounting onto a machined housing face Outer ring rotation or inner ring rotation Not required — no separate fixing flanges or support seats Improved system rigidity versus traditional segmented bearings, with minimal installation impact on performance Bore 40–384 mm, outer diameter up to 646 mm, width 22–79 mm; match PCD1 and PCD2 to your bolt circle
XSU Not published on this page — confirm with supplier Confirm with supplier Confirm with supplier Confirm with supplier Confirm with supplier Ask whether the rings are split, how holes are provided and which ring is driven
SX Not published on this page — confirm with supplier Confirm with supplier Confirm with supplier Confirm with supplier Confirm with supplier Ask for the ring arrangement, mounting face and available bore range
YRT Not published on this page — confirm with supplier Confirm with supplier Confirm with supplier Confirm with supplier Confirm with supplier Ask whether it suits a rotary table platen and what axial height it adds
RB-style Not published on this page — confirm with supplier Confirm with supplier Confirm with supplier Confirm with supplier Confirm with supplier Ask which ring is split, how preload is set and whether flanges are included

Selection Decision Tree: Four Branching Questions

Answer the four questions in order. Each one narrows the structural family, not the part number, so you end up comparing like with like when you approach a supplier.

Question 1

Which load direction dominates?

If the axis sees axial load and tilting moment alongside radial load — a rotary table platen, a trunnion, a joint — you need one component carrying all three. If the load is almost purely radial, a radial-only arrangement can be enough.

Leads to: crossed roller layout where combined load and moment dominate; radial arrangement where it does not.

Question 2

How much axial space is available?

A short stack forces a single-bearing solution. A deep housing gives you the option of two spaced bearings with a preload set.

Leads to: single crossed row when height is tight; paired arrangement when height is free.

Question 3

Which ring rotates?

Some designs drive the inner ring and fix the outer; others do the reverse for access or for cable routing. Confirm the family supports your choice before you design the housing.

Leads to: XU operates in both outer ring and inner ring rotation scenarios, so either layout stays open.

Question 4

Bolt-on face mounting or clamped mounting?

If the housing already has a machined face and a bolt circle, a bearing with pre-machined holes keeps assembly simple. If you plan to clamp through separate flanges or a support seat, the housing needs more parts and more machining.

Leads to: integrated face-mount construction when you want to remove flanges and seats from the design; flange-based families when your existing hardware already includes them.

Integrated Face-Mount Anatomy: What the XU Structure Changes

The XU Series is built around one idea: the bearing and its mounting hardware become a single part. That changes the housing drawing as much as it changes the bearing itself.

XU Series crossed roller bearing showing integrated inner and outer ring with mounting holes
Integrated inner and outer ring construction with pre-machined mounting holes on the XU Series.
  • Integrated ringsInner and outer rings are built as one integrated unit with the housing, so the bearing keeps its geometry while it is being installed.
  • Holes already thereMounting holes are pre-machined into the rings, so the bearing bolts straight to a machined face without a separate drilling step.
  • No extra hardwareSeparate fixing flanges and support seats are not required, which removes parts from the bill of materials.
  • Either ring can rotateThe design operates in both outer ring and inner ring rotation scenarios, keeping housing layout flexible.
  • Stable rotationThe published performance is stable rotational accuracy with consistent, uniform torque.
  • Less assembly distortionMinimal installation impact on performance, with deformation during mounting minimised so published tolerances and rotational accuracy are preserved.
  • Rigidity and running behaviourReduced assembly complexity and improved system rigidity versus traditional segmented bearings, with lower vibration and frictional loss contributing to longer service life and lower maintenance.

Buyer decision: if the housing already has a finished face and a bolt circle, the integrated structure removes flange design work and one assembly tolerance chain. If the housing cannot be machined flat and square, plan the face preparation first — the bearing has no support seat to compensate for an uneven mounting surface.

XU Sizing Walk-Through: Reading the Table and Shortlisting

The published table gives you the bore, the outer envelope, both hole circles and the mass for every model. Read the columns in this order and the shortlist usually falls out on its own.

  1. Start with the bore (D). Match the shaft or spindle diameter against the first D column. The published range runs from 40 mm to 384 mm.
  2. Check the outer envelope. The second D column and the overall height H have to fit your housing. Outer diameters reach 646 mm and widths run from 22 mm to 79 mm across the range.
  3. Confirm the bolt circles. PCD1 and PCD2 give the two hole circles, and φ/M describes the hole count and thread or clearance form, so you can compare them directly with your existing face pattern.
  4. Check rotation mode and mass. Both rings can rotate on XU, and M in kilograms feeds straight into the moving-mass budget of the axis.
Model D (mm) δd (mm) D (mm) δD (mm) B (mm) B1 (mm) H (mm) δH (mm) Dpw (mm) PCD1 (mm) φ/M (mm) PCD2 (mm) φ/M (mm) M (Kg)
XU050077400/0.0251120/-0.040222122±0.177566-M8976-φ7-φ11*6.41.4
XU060094570/0.0251400/-0.040262526±0.194706-M81206-φ9-φ15*82.4
XU080120690/0.0201700/-0.040302930±0.1120906-M81486-φ9-φ15*84
XU1202221400/0.33000/-0.2303036±0.122217012-φ1827012-M612
XU1602601910/0.0723290/-0.089414146±0.126021520-φ1430520-φ1416
XU3005153840/0.0896460/-0.089797986±0.151543218-φ2659818-φ26115
D (mm) Bore diameter in the first column and outer diameter in the second, exactly as published on the product page.
δd / δD / δH Published tolerance bands for bore, outer diameter and height on each model.
B / B1 / H Ring widths and the overall bearing height.
Dpw Roller pitch circle diameter — the running centreline of the crossed rollers.
PCD1 / PCD2 The two mounting hole circles, one on each ring face.
φ/M Hole pattern description: count, thread or clearance form and counterbore detail.
M (Kg) Published unit mass, useful for moving-mass and handling checks.

Shortlist tip: if you have two candidate models, compare the δd and δD tolerance bands before the hole patterns — those bands decide how much preload and running accuracy the finished axis can hold. Need help matching a hole pattern to an existing housing face? Request a custom quote.

Application Fit Notes: Rotary Table, Semiconductor Unit, Robot Joint

Three common rotary axis profiles, each with the requirement that usually drives the bearing choice and the XU characteristic that answers it.

XU Series crossed roller bearing face detail for rotary table mounting

CNC rotary table

Requirement
A platen that holds axial load and tilting moment under cutting force, bolts to a machined face, and keeps the table height low.
XU fit
Direct face mounting with pre-machined holes removes flanges and support seats, and the integrated rings improve system rigidity.
Decision
Compare PCD2 and the φ/M hole pattern against your platen bolt circle before ordering; large models such as XU300515 reach a 384 mm bore and 115 kg mass, which changes handling and lift planning.
XU Series crossed roller bearing with uniform torque running surfaces for compact rotary units

Semiconductor rotary unit

Requirement
A compact envelope with smooth, repeatable motion, where installation stress must not show up as torque variation.
XU fit
The integrated structure minimises deformation during installation, and the published performance is stable rotational accuracy with consistent, uniform torque.
Decision
Check bore and outer diameter against the enclosure first, then compare the δd and δD tolerance bands of the two closest models.
XU Series crossed roller bearing inner ring view for robot joint rotary axes

Robot joint

Requirement
One compact joint carrying combined moment and radial load, with low moving mass and simplified assembly.
XU fit
A single crossed row replaces two spaced bearings, and either ring can be the rotating one depending on how the joint is driven.
Decision
Use the M value per model to test the moving-mass budget, and confirm which ring is driven so the housing and bolt circles are laid out correctly.

Send Your Requirements, Get a Candidate and a Drawing

The XU Series is quoted through a custom quote route rather than a fixed cart. Send the axis details and the reply comes back with a candidate model and a drawing to check against your housing.

  • Bore or shaft diameter, and the outer envelope your housing allows
  • Load direction and magnitude — radial, axial and tilting moment
  • Operating speed and duty cycle
  • Mounting face and bolt circle, including PCD1 or PCD2 if already fixed
  • Which ring rotates and which ring is fixed
  • Quantity, delivery expectation and any drawing or marking requirement
XU Series crossed roller bearing ready for a custom quote request

Related Reading

Three notes to help clarify product requirements before contacting the supplier.

Precision Crossed Roller Bearings for Compact Semiconductor Rotary Units

Compact semiconductor rotary units need a bearing that fits a thin axial envelope while carrying radial, axial, and moment loads, so fit review starts with assembly dimensions and inspection data.

Read article

What Mounting Holes Are Needed on an Integrated Crossed Roller Bearing?

Mounting holes turn an integrated crossed roller bearing into a bolt-on rotary interface, so the hole pattern must be read as part of the machine design rather than as a separate accessory detail.

Read article

How to Choose a Face Mount Crossed Roller Bearing for CNC Rotary Tables

Face mount crossed roller bearing selection for a CNC rotary table starts at the table face and proceeds through load path, rotation mode, envelope, bolt circle, and model number.

Read article

Frequently Asked Questions

What information is shown for this product?

review the product details, images, and specifications presented on the official product page.

Where can i check the intended application?

use the application and use-case information published on the official product page.

Which specifications should i confirm before ordering?

confirm the specifications and options listed for the exact product variant before placing an order.

Where can i check available options?

check the official product page or ask the supplier about options shown for the selected product.

How can i request product information?

use the official contact or inquiry path provided on the site.

What should i include in an inquiry?

include the product page, intended use, required quantity, and any specifications you need the supplier to review.