欢迎来到我们的博客

我们正在分享我们最感兴趣的领域的知识。
click

Integrated and Split Crossed Roller Bearing Ring Structures

来自 rockbearing November 5th, 2026 7 浏览次数

Introduction: The ring structure of a crossed roller bearing decides where bolt clamp force travels, how many interfaces need alignment, and how assembly stack-up enters a rotary axis.

When two crossed roller bearing designs share a similar envelope, the difference often hides in the ring. A split ring needs a flange, housing, or clamp feature to hold it in place. An integrated ring carries its own mounting holes and bolts directly to a machined face. That difference changes what the assembly team adjusts, what the designer must tolerance, and where deflection can enter the structural loop. The useful comparison is not “old design versus new design. ” It is a comparison of load paths through the mounting interface.

What Split and Integrated Ring Structures Change in a Rotary Assembly

In a rotary assembly, the bearing ring is part of the structural loop between the machine frame and the rotating output. It is not just a raceway. The ring face may act as a mounting datum, the ring body may carry clamp load into the raceway region, and the bolt pattern may control how evenly that load is spread. A split ring and an integrated ring place those duties in different parts of the assembly, so they change the mounting sequence as much as the bearing itself. A face mount crossed roller bearing with pre-machined end-face holes shortens that loop. The XU series reference describes one-piece inner and outer rings with pre-machined end-face holes, direct bolt fixing without a separate flange or bearing housing, and support for inner or outer ring rotation. The published XU reference centers on ring geometry and face holes; material grade and preload remain separate data points for a project review. The structural point is simple: the ring body itself becomes the mounting body. Split designs follow a different logic. A split outer ring or split inner ring can be practical for assembly, inspection, or preload adjustment, especially when the surrounding machine structure already has a housing or flange. The ring may be located radially by a housing bore and clamped axially by a flange or cover. That arrangement can work very well, but it adds interfaces between the bolt and the raceway. Each interface has flatness, perpendicularity, burr, paint, shim, and torque-order effects. None of those effects is automatically a failure; they are simply additional variables in the assembly stack-up. The practical change is where the designer puts the precision. An integrated ring asks for a flat, perpendicular mounting face and a hole pattern that matches the ring. A split ring asks for a housing bore, flange contact face, clamp sequence, and often an alignment check before the axis is shimmed. One design is not universally better. The question is whether the machine frame can provide the mounting face, or whether the assembly needs a separate flange and housing to hold the ring.

How Bolt Force Travels Through the Mounting Interface

Bolt force is often described as “clamping the bearing,” but the mechanical path matters more than the phrase. A tightened bolt creates tension in the bolt and compression in the parts between the bolt head and the threads. That compression travels through every contact face in the joint. If the path is short and direct, the clamp load reaches the ring body with fewer interruptions. If the path passes through a flange, housing, or split ring interface, each contact face can change how evenly the load spreads.

1. Integrated Rings Carry Clamp Load Through One Continuous Body

With an integrated ring, the bolt passes through a frame-side hole or clamp feature and threads into the ring’s end-face hole. The clamp force compresses the ring face against the mounting face, then travels through the one-piece ring body toward the raceway region. The ring is continuous around its circumference, so the bolt pattern can distribute compression around the full ring rather than through a separate flange first. The main interface is the ring-to-frame face, and that face becomes the critical flatness and perpendicularity datum. This arrangement removes the flange-to-ring interface from the load path, but it does not make the ring infinitely stiff. The ring still deflects under load, and bolt spacing, ring thickness, face contact, and bearing preload all shape the final behavior. The advantage is that the clamp load has a short, direct route into the ring body. On the assembly floor, that usually means fewer parts to align before the rotary axis is shimmed. The tradeoff is that the machine frame must provide a suitable mounting face, and the bolt torque pattern must be controlled so the ring is not pulled into a distorted shape.

2. Split Rings Add a Separate Flange and Ring Interface

With a split ring, the bolt force often enters a flange, cover, or housing before it reaches the bearing ring. The path may run from the frame into the flange, from the flange into the outer ring, and from the ring into the rolling elements. If the design uses a split inner ring, a similar chain can appear on the shaft side. Each added contact face must be flat, clean, and square enough for the clamp load to spread evenly. The flange may also locate the ring radially, so the housing bore and flange pilot become part of the alignment stack. This is why split crossed roller bearings often need an external flange or housing. The flange can clamp the ring axially, the housing can locate it radially, and the two features together hold the ring in the machine structure. That can be a sound design, especially where the housing already exists or where the ring must be assembled around a shaft. The cost is stack-up. The flange face, ring face, housing bore, and frame face all contribute to the final position of the raceway. Assembly teams commonly see extra alignment checks in these joints before the rotary axis is shimmed, because the clamp load is passing through more than one interface. A split design is not a defect. It is a different mounting strategy. The designer should expect the flange and housing to carry alignment and clamp duties, and the assembly plan should reflect that. The ring may perform well, but the load path now includes the flange and housing, so their flatness, fit, and bolt sequence become part of the bearing’s working environment.

Why the Comparison Is About Load Paths, Not Only Part Count

Part count is easy to see. A split design has more pieces on the drawing, and an integrated design looks simpler. But part count alone does not explain why one assembly is easier to align or why one design holds preload more consistently. The mechanical difference is the route the clamp force takes. A short route through a continuous ring body reduces the number of contact faces that can tilt, gap, or compress unevenly. A longer route through a flange and housing adds contact faces that must be controlled together. This is also why a roller bearing supplier can show the same envelope dimensions for both designs while the mounting behavior differs. The bearing may fit the same space, but the frame preparation and assembly sequence can be different. A design team reviewing a precision roller bearing company’s drawing set should ask where the bolt clamp force enters the ring, which face sets the axial datum, and which interface controls radial alignment. Those questions matter more than counting parts. On a custom bearing project, the mounting interface is often the part that changes the most. The load-path view also keeps the comparison honest. Integrated rings do not eliminate deflection, and split rings do not always cause misalignment. A well-machined split assembly with a rigid flange and a properly fitted housing can perform predictably. A poorly prepared integrated mounting face can still distort a ring. The real difference is where the compliance and alignment work sit: in the ring body and frame face, or in the flange, housing, and split ring interface. That is the distinction worth carrying into a design review.

Conclusion

Integrated and split crossed roller bearing rings differ most in how bolt clamp force reaches the raceway. An integrated ring carries clamp load through one continuous ring body and a direct face interface. A split ring carries clamp load through a flange, housing, or clamp feature before it reaches the ring, so alignment and stack-up move into those interfaces. Neither layout removes the need for flat faces, controlled torque, and careful assembly. For readers reviewing a face mount crossed roller bearing for a compact rotary axis, the useful next step is to compare the drawing’s ring geometry, mounting faces, and the number of interfaces between frame and output.

FAQ

Q: What changes when crossed roller bearing rings are integrated instead of split?

A: The main change is the mounting load path. An integrated ring has one-piece inner and outer rings with face holes, so bolt clamp force travels directly from the frame into the ring body. A split ring usually needs a flange, housing, or clamp feature to hold the ring, which adds contact faces between the bolt and the raceway. That changes alignment checks, stack-up points, and assembly sequence more than it changes the basic rolling geometry.

Q: Why do split crossed roller bearings often need an external flange or housing?

A: A split ring needs a reliable way to be located and clamped in the machine structure. The flange can provide axial clamping, while the housing can provide radial location. Together they hold the ring and help control preload. The tradeoff is that the flange and housing become part of the load path, so their flatness, fit, and bolt sequence affect how evenly clamp force reaches the ring.

Q: Does an integrated ring design remove the need to control bolt preload?

A: No. An integrated ring shortens the load path, but bolt preload still controls how evenly the ring face is compressed. Uneven torque, poor face flatness, or a soft mounting surface can distort the ring and affect raceway behavior. The designer still needs a suitable mounting face, a controlled torque pattern, and a check that the ring is seated correctly before the axis is put into service.

Sources / References

Capstone Design | Undergraduate | Mechanical Engineering | Purdue University

Lecture Notes | Design and Manufacturing I | Mechanical Engineering | MIT OpenCourseWare

Related Examples

XU Series Crossed Roller Bearings

上一页
Precision Crossed Roller Bearings for Compact Semiconductor Rotary Units
阅读更多
下一页
Crossed Roller Bearings Support CNC Rotary Table Rigidity
阅读更多